Environmental Test Chambers

Environmental Test Chambers

Environmental Test Chambers

Environmental test chambers, also known as Climate Chambers or Climatic chambers, are controlled, artificial spaces that recreate environmental conditions. Conditions that simulate changes and stresses that an object will likely encounter during its productive lifetime. The goal is to test and study the long-term effects of said conditions on industrial and electronic products, materials, and miscellaneous components.

Tayyab Trading’s portfolio of test chambers includes:

  • Temperature
  • Test Chambers
  • Climate Test Chambers
  • Corrosion Chambers
  • Weather Testers
  • IP dust & rain chambers
  • Ozone test chambers,
  • Noxious gas SO2 H2S chambers,
  • Walk-in chambers

Our Test chambers are tested and approved by CE, CSA, RoHS, TUV, SGS and ISO17025 calibration.

In addition to installing the chambers will also provide support for commissioning, calibration & trial runs.

A detailed run down of different chambers and their capabilities are shown below.

3 Years Warranty - 20+ Years of Product Life

Benchtop Temperature humidity Test Chambers are Small, bench-top test chamber for simulating temperature and humidity environments. Includes only temperature and humidity test chambers. Widely used in electronics, automotive, manufacturing, research and laboratories. Few advantages are small, desktop, small footprint, portable, stable performance and Full function.

Our climate and humidity test chambers are available in a variety of sizes and configurations, ranging in size from 50L to 3000L, Bench-tops, floor and walk-in Models.

To perform temperature & humidity test, cold resistance test, thermal cycle test, ultra low temperature test, high temperature test, storage condition, and calibration function.

Over 29 different models let you choose size, configuration and performance to suit many types of environmental test conditions. Temperature change rates from 1-15°C/min.

Low temperature available:

  • -20℃
  • -40℃
  • -70℃
  • -86℃
  • -200℃( liquid nitrogen refrigeration.

To perform cold resistance test, thermal cycling test, ultra low temperature test, high temperature test, storage condition, and calibration function.

Environmental test chamber for PV modules (solar panels) thermal cycling, humidity freeze cycle, and damp heat RH testing, to test whether PV modules can withstand high temperature with humidity and low temperature, to test its fatigue and thermal failure after temperature repeated changes, to confirm its thermal stress PV modules generated under high humidity circumstance and capability of long-term resistance to moisture penetration. This test chamber is widely used in solar panels testing.

Different models let you choose size, configuration and performance to suit many types of solar panels for IEC, UL test methods.

2-zone hot cold thermal shock test chamber is available in small capacity and large capacity to meet different testing requirements. The specimen automatic transferred from cold chamber to hot chamber by basket.The basket slides vertically and smoothly through rails, to make the specimen is exposed to the two chambers.

Thermal shock test chamber has upgraded to touch-screen controller with Ethernet, you are easy to operate over network.

Our thermal shock test chamber is just one chamber for test room, it circulates cold and hot air through the pneumatic damper on the left and right sides.This design makes external size smaller, thermal shock chamber are pre-heated and pre-cooled to achieve faster test temperature.

The test chamber can pre-record the programs, so that customers can start test only by clicking program numbers. Standard and custom models can meet any user requirements.

Salt spray test chamber is used to test the anti-corrosion quality of all the materials surfaces of painting, coating, electroplating in condition of salt spray environment. Basic salt spray test chambers meet ASTM, ISO, IEC and other International Standards test methods, capacity available in 108L, 320L, 410L, 780L, 1000L, 1600L capacity.

Cyclic salt spray  chamber is different from basic salt spray test chamber. Cyclic corrosion test chamber exposes sample to a series of different environments in repetitive cycles that incorporate temperature , humidity, salt spray and dry. Accelerated corrosion test methods included ASTM B117, ASTM BG85, ISO9227, IEC60068-2-52, iec61701-2, ISO7253 and many others.

SC series corrosion chambers are upgrade to programmable controller and Ethernet access. All models are automated, and can working continuously. Various models can meet different test requirements.

Xenon arc chambers reproduce weathering damage by sunlight, temperature, humidity and water spray. Xenon weathering test chambers are utilized in textiles, dyes, leather, plastics, paints, coatings, automotive interior parts, color building materials. To perform weathering test, color fastness tests, aging test, hardening test, softening test, crack. Accelerated weathering test methods included ISO4892, ASTM G155-1/155-4, ISO 105-B02/B04/B06, ISO11341, AATCC TM16, TM169, , JIS L0843, SAEJ1960/1885, JASOM346, and many others.

Xenon weathering chambers can place 42 pieces of specimens, are upgrade to programmable controller and Ethernet access. Their reliable performance and low purchase price make these products very competitive.

UV test chamber is used in tests that incorporate UV light, temperature, condensing humidity, water sprays, and irradiance control. UV weathering resistance test chamber uses UVA-340, UVB-313 fluorescent UV lamps for a variety of test conditions. Accelerated weathering tests included color change, gloss loss, chalking, cracking, crazing, hazing, blistering, strength loss and oxidation and many others.

UV series weathering chambers are upgraded to programmable controller and Ethernet access that provides simple operation and control.

These small size dust test chambers are capacity of 800 liters and 1000 liters. Considering that some specimens are smaller and less, so we designed and produced this small dust chambers.

Sand and dust test chambers are made for the simulation of dust and sand conditions. These dust test chambers are used to test the exposure of test the exposure of automotive and electronic components under extreme environmental conditions in order to validate product seal.Dust ingress test methods included IEC60529, ISO20653 and many others.

The airflow circulates upward from the bottom, blowing the dust circulation,forcing dust around the specimens. All models are upgraded to programmable controller and Ethernet access that provides simple operation and control.

Larger series sand and dust test chambers  allows for the large and more quantity specimens, capacity of 1500 liters and 2000 liters as standard. Great for laboratories and large industrial products.

Sand and dust test chambers are made for the simulation of dust and sand conditions. These dust test chambers are used to test the exposure of test the exposure of automotive and electronic components under extreme environmental conditions in order to validate product seal.Dust ingress test methods included IEC60529, ISO20653,MIL-STD-810G and many others.

The airflow circulates upward from the bottom, blowing the dust circulation,forcing dust around the specimens. All models are upgrades to programmable controller and Ethernet access that provides simple operation and control.

LIB Water spray test chambers can perform tests in accordance with IEC60529, and IPX1 IPX2 IPX3 IPX4 protection code.The chambers built with the water tightness of sealed components such as head lamp, Power connector. Waterproof power connector in the test room can easily supply electricity to the specimens.

The water spray Chamber built with a water re-circulation system that reduced water use and a series of water pipes. Incorporated rotating turntable can promote even spray of water over the surface of the products under testing. Automatic water supply ensures adequate supply of water and automatic testing. All models are upgrade to programmable controller and Ethernet access that provides simple operation and control. Various size and configuration to suit many types of test conditions.

IPX5 IPX6 Water Jetting Test Chamber is applied to test the watertightness of enclosures of automotive parts, outdoor lamps and electronics parts.

The chambers built with the water tightness of sealed components such as head lamp, Power connector. Waterproof power connector in the test room can easily supply electricity to the specimens.

IPX5 and IPX6 functions on one test chamber,make testing convenient and cost-effective.

IPX7 X8 water immersion tank is used to test to test the water tightness of enclosures of automotive parts, outdoor lamps and electronics parts.

IPX7 IPX8 immersion chamber built with a water re-circulation system that reduced water use and a series of water pipes. Automatic water supply ensures adequate supply of water and automatic testing.

IPX7 and IPX8 functions on one test chamber,make testing convenient and cost-effective.

IPX9K test chamber is widely used in the electronics, military and consumer product industries. IPX9K is the highest rating currently available for water ingress protection in accordance with IEC 60529 and ISO 20653.

Products under test is subjected to high pressure (8000 – 10000 Kpa), high temperature (+80°C) and water jets at a flow rate of 14 – 16 L/min.

IPX9K chamber built with a water re-circulation system that reduced water use and a series of water pipes. Automatic water supply ensures adequate supply of water and automatic testing.

All models are upgrade to programmable controller and Ethernet access that provides simple operation and control.

ozone resistance test chambers test elastomers (rubber) in the condition of ozone exposure,to simulate and measure rubber aging by means of ozone within a few days.

Built with dynamic and static sample holders and others in accordance with test method of ASTM D1149, IEX6006811-403, ISO1431, ASTM D1171.All models are upgrade to programmable controller and Ethernet access that provides simple operation and control.

SO2 Noxious Gas Test Chambers reproduce damages by temperature, relative humidity and noxious gas Corrosion to material, components and constructions.

This noxious gas chamber can be used for single gas tests and mixed gas tests.Test methods are in accordance with IEC 60068-2-42, IEC60068-2-60 and other standards.

LIB designed and produced high temperature drying ovens at temperatures up to +250°C, +500°C, +800°C, +1000°C, +1200°C with small, medium and large volumes.

Ovens are used for high temperature drying, paint drying, drying glass and plastics, ink, and removing moisture, wood drying and high temperature tests. Applied to aerospace, automotive, electronics, metalworking.

Drying ovens are available in various sizes and temperature ranges, including standard and custom oven.

LIB Industry designs and manufactures walk in chambers. These walk-in chambers are in piece assembling structure, which enables on-site installation and commissioning. With large volume, the chamber can be used to simulate the single or complicated environmental factors in the atmosphere such as temperature, humidity, salt fog, illumination, dust, rain and vibration. The products can be used to analyze and evaluate the property and performance of the batch elements and parts or machine sets under simulated conditions, and can also be used in experiment and production.